Davey HS Series Electric Pumps Bedienungsanleitung PDF herunterladen

Priming and Operation

1. Ensure outlet nearest to pump is

open.

2. Fill pump body and suction

line through priming plug hole

located above suction inlet and

replace plug.

Please pass these instructions on to the operator of this equipment.

Installation and

Operating Instructions

for Dynao

HS Series Electric Pumps

MODELS: HS50-06, HS60-08

Trouble Shooting Check List

MOTOR OPERATING BUT NOT PUMPING

1. Suctionlineandpumpbodynotlledwithwater.

2. Leaking foot valve.

3. Airleaksinsuctionlinesorsuctionpipenotunderwater.

4. Airtrappedinsuctionlines(alsopossiblewithoodedsuction)dueto

unevenriseinpiping(eliminatehumpsandhollows).

5. Nowateratsourceorwaterleveltoolow.

6. Valve on suction or delivery lines closed.

MOTOR NOT RUNNING

1. Powernotconnected.

2. Supplyvoltagetoolow.

3. Overload tripped.

4. Motor not free to turn e.g. a blocked impeller.

5. Internal motor fault.

MOTOR RUNS FOR SOME TIME THEN STOPS - RESTARTS

AUTOMATICALLY AFTER SHORT TIME

Overloadtrippinginmotor -lowvoltageatmotorterminals

- motor in direct sunshine or in “hot box”

  - motornotfreetoturn(eg:blocked)

After Sales Service

For professional after sales service or repair contact your Davey Dealer.

For assistance in locating your nearest dealer contact the Davey Support

Centre on 1300 2 DAVEY.

3. Switchon.

4. Prime should establish almost

immediatelywithastrongow

ofwater,however,insome

installations it may be

necessary to repeat

the above operation

to remove all air from

the system.

WARNING:

DO NOT RUN DRY.

DO NOT RUN WITH LOSS OF PRIME.

DO NOT PUMP WATER CONTAINING ABRASIVE MATERIALS.

*NOTE “MOTOR PROTECTION DEVICE” :

For protection, the Davey pump motor is tted with an automatic

reset thermal overload, constant tripping of this overload indicates a

problem e.g. low voltage at pump, excessive temperature (above 50°C)

in pump enclosure.

WARNING: Automatic reset thermal overloads will allow the pump to

restart without warning. Always disconnect the pump motor from the

electrical supply before maintenance or repairs.

WARNING: When servicing or attending pump, always ensure power

is switched off and lead unplugged. Electrical connections should be

serviced only by qualied persons.

Care should also be taken when servicing or disassembling pump to

avoid possible injury from hot pressurised water. Unplug pump, relieve

pressure by opening a tap on the discharge side of the pump and allow

any hot water in the pump to cool before attempting to dismantle.

IMPORTANT:

DO NOT USE petroleum based uids or solvents (e.g. Oils, Kerosene,

Turpentine, Thinners, etc) on the plastic pump components or seal

components.

Connection of Mains Scheme or Town Water Supply

to either Suction or Discharge of Pumps

Most Water Supply Authorities have strict regulations regarding direct

connectionofpumpstomainswatersupplies.Inmostcasesanisolatingtank

isrequiredbetweenmainssupplyandpump.Daveyalsorecommendthis

method. Directly applied mains pressure can exceed pump operating pressure

and damage pump.

Davey Water Products Pty Ltd can not accept responsibility for loss or

damage resulting from incorrect or unauthorised installations.

Davey

Repair or Replacement Guarantee

In the unlikely event in Australia or New Zealand that this Davey product develops any malfunction within two years of the date of original purchase due to

faulty materials or manufacture, Davey will at our option repair or replace it for you free of charge, subject to the conditions below.

Should you experience any difculties with your Davey product, we suggest in the rst instance that you contact the Davey Dealer from which you

purchased the Davey product. Alternatively you can phone our Customer Service line on 1300 367 866 in Australia, or 0800 654 333 in New Zealand, or

send a written letter to Davey at the address listed below. On receipt of your claim, Davey will seek to resolve your difculties or, if the product is faulty or

defective, advise you on how to have your Davey product repaired, obtain a replacement or a refund.

Your Davey Two Year Guarantee naturally does not cover normal wear or tear, replacement of product consumables (i.e. mechanical seals, bearings or

capacitors), loss or damage resulting from misuse or negligent handling, improper use for which the product was not designed or advertised, failure to

properly follow the provided installation and operating instructions, failure to carry out maintenance, corrosive or abrasive water or other liquid, lightning

or high voltage spikes, or unauthorized persons attempting repairs. Where applicable, your Davey product must only be connected to the voltage shown

on the nameplate.

Your Davey Two Year Guarantee does not cover freight or any other costs incurred in making a claim. Please retain your receipt as proof of purchase; you

MUST provide evidence of the date of original purchase when claiming under the Davey Two Year Guarantee.

Davey shall not be liable for any loss of prots or any consequential, indirect or special loss, damage or injury of any kind whatsoever arising directly

or indirectly from Davey products. This limitation does not apply to any liability of Davey for failure to comply with a consumer guarantee applicable to

your Davey product under the Australian or New Zealand legislation and does not affect any rights or remedies that may be available to you under the

Australian or New Zealand Consumer Legislation.

In Australia, you are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You

are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Should your Davey product require repair or service after the guarantee period; contact your nearest Davey Dealer or phone the Davey Customer Service

Centre on the number listed below.

For a complete list of Davey Dealers visit our website (davey.com.au) or call:

* Installation and operating instructions are included with the product when purchased new.

They may also be found on our website.

P/N 402105

AUSTRALIA

Davey Support Centre

6 Lakeview Drive,

Scoresby, Australia 3179

Ph: 1300 367 866

Fax: 1300 369 119

Website: davey.com.au

Davey Water Products Pty Ltd

Member of the GUD Group

ABN 18 066 327 517

NEW ZEALAND

Davey Support Centre

7 Rockridge Avenue,

Penrose, Auckland 1061

Ph: 0800 654 333

Fax: 09 527 7654

Website: daveynz.co.nz

® Davey is a registered trade mark of Davey Water Products Pty Ltd.

1 2

Inhaltsverzeichnis

Seite 1 - HS Series Electric Pumps

Priming and Operation1. Ensure outlet nearest to pump is open.2. Fill pump body and suction line through priming plug hole located above suction inl

Seite 2

IP55 Compliant ConnectionForsomeinstallations,suchaswetareasindairies,thepumpisrequiredtobeIPX5compliant.TheDynao® HS pump is IP55

Kommentare zu diesen Handbüchern

Keine Kommentare

Davey HS Series Electric Pumps Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Pumpen Davey HS Series Electric Pumps herunter. Davey HS Series Electric Pumps User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Pumpen Davey HS Series Electric Pumps